Proof
What has been run, on what, and when.
- Proven on vehicles
- Used on real vehicles.
- Proven in daily use
- Carrying real work every day.
- Proven on the bench
- Run on real hardware on our bench.
- Proven in self-test
- Passing its automated self-tests.
- Proven against simulators
- Run end to end against protocol simulators.
Proven on vehicles
J2534 pass-thru with OEM software
As of 21 November 2026
The IgniteRemote J2534 link, with a pass-thru interface at the vehicle, has been used on real vehicles with Ford FDRS and FJDS, Chrysler wiTECH, JLR SDD and Nissan CONSULT-III plus, key programming included.
The vehicle maker's own software runs on your computer and drives the car through the IgniteRemote J2534 link, so the subscription and its login stay with you.
Proven in daily use
Link check before a write
As of 21 November 2026
In service on the J2534 path, where it has refused real programming attempts over a poor connection, and run on the bench refusing an unmeasured link.
The link is measured before a programming sequence may start. A link that cannot be measured, or measures badly, is refused with the reason in plain words.
Encrypted link, short-lived job authority
As of 21 November 2026
The same transport carries IgniteRemote's J2534 tool links every day.
Traffic between the box and your dock is encrypted, and a job is a lease the server grants for that job only, never a standing permission.
Proven on the bench
CAN on pins 6 and 14
As of 21 November 2026
A diagnostic tool on one bench read ten live fault codes from an engine control module on another bench, through the link, with no relay server in the path (20 September 2026).
The main diagnostic bus on every car sold in the US since model year 2008, carried frame for frame between the car and your tool.
CAN FD
As of 21 November 2026
FD frames with bit-rate switching verified through the shop-side CAN FD interface on the bench.
Both ends use CAN FD interfaces, so FD frames with bit-rate switching are carried as FD frames.
Tool Tunnel
As of 21 November 2026
A standalone diagnostic tool read live fault codes from an engine control module bench to bench, through the tunnel (20 September 2026).
Your own key programmer or diagnostic tool stays at your shop, plugged into the dock, and behaves as though the car were on the bench in front of it.
Bus health in plain words
As of 21 November 2026
Automatic bus-off recovery ran 37 times in one bench session without ending it.
The box recovers from bus-off by itself and tells the technician what the bus is doing, naming the likely cause.
Nothing to type
As of 21 November 2026
How every bench job has been started since September 2026.
A box is enrolled once with a setup code. After that the technician picks it from a list and presses Start: no addresses, ports or tokens at either end.
Online by network cable
As of 21 November 2026
Verified on the box (November 2026).
Plug a cable from any router into the box. It is online in about a minute with nothing typed.
Online by phone lead
As of 21 November 2026
iPhone tethering verified on the box (November 2026).
Plug a phone into the box's USB port and turn on tethering (Android) or Personal Hotspot (iPhone). Nothing is configured on the box.
Online by its own setup Wi-Fi
As of 21 November 2026
Setup network and setup page verified on the box (November 2026).
With nothing plugged in, the box raises its own setup network. Join it from a phone, pick the Wi-Fi it should use, and it is online in about a minute. It remembers a network that worked.
Proven in self-test
Second CAN pair on pins 3 and 11
As of 21 November 2026
Passing 1,180 self-test checks, including two real tunnel processes on the Linux kernel's own CAN sockets (21 November 2026).
The secondary bus some makes put on pins 3 and 11 (Ford's medium-speed CAN is the best known), carried in the same job as pins 6 and 14. The box listens first and joins the pair only when it hears a CAN bus there.
Diagnostic priority lane
As of 21 November 2026
Self-tested against a flood of 3,000 frames a second with every diagnostic answer back in under 250 ms (21 November 2026).
Your tool's questions and the car's answers travel ahead of the bus's background chatter, so a busy bus does not make a tool time out.
Proven against simulators
DoIP diagnostics (ISO 13400)
As of 21 November 2026
Discovery, routing activation and diagnostic reads through the relay run end to end against DoIP simulators (21 November 2026).
For cars that do their diagnostics over Ethernet: the box finds the vehicle, opens routing and relays diagnostic reads and scans to a tester at your shop.
J2534
OEM software the J2534 link is used with.
| Software | How it is used |
|---|---|
| Ford FDRS / FJDS | Used on vehicles. |
| Chrysler wiTECH | Used on vehicles regularly. |
| JLR SDD | Used on vehicles. |
| Nissan CONSULT-III plus | Used on cars, key programming included (J2534 v05.00). |
| GM Techline Connect | Runs as a J2534 pass-thru client. |
| Toyota Techstream | Runs as a J2534 pass-thru client. |
| Volvo VIDA | Runs on a J2534 interface, 2016 and newer included. |
| VW / Audi ODIS | J2534 vehicles. |
| BMW ISTA | J2534 models. |
Launching mid-December 2026
Put your bench in a car that is somewhere else.
Reserve a box from the first batch today for $99, refundable until it ships. Or join the list and get the introductory price before it is public.